The Direct Partial Oxidation of Methane to Dimethyl Ether over Pt/Y2O3 Catalysts Using an NO/O2 Shuttle

Using a mixture of NO + O₂ as the oxidant enabled the direct selective oxidation of methane to dimethyl ether (DME) over Pt/Y₂O₃. The reaction was carried out in a fixed bed reactor at 0.1 MPa over a temperature range of 275–375 °C. During the activity tests, the only carbon‐containing products were DME and CO₂. The DME productivity (μmol g_cat^?1 h^?1) was comparable to oxygenate productivities reported in the literature for strong oxidants (N₂O, H₂O₂, O₃). The NO + O₂ mixture formed NO₂, which acted as the oxygen atom carrier for the ultimate oxidant O₂. During the methane partial oxidation reaction, NO and NO₂ were not reduced to N₂. In situ FTIR showed the formation of surface nitrate species, which are considered to be key intermediate species for the selective oxidation.     

Improving the Yield and Rate of Acid-Catalyzed Deconstruction of Lignin by Mechanochemical Activation

Lignin is a potential biomass feedstock from plant material, but it is particularly difficult to economically process. Inspired by recent ball-milling results, state-of-the-art quantum mechanochemistry calculations have been performed to isolate and probe the purely mechanochemical stretching effect alone upon acid-catalyzed deconstruction of lignin. Effects upon cleavage of several exemplary simple ethers are examined first, and with low stretching force they all are predicted to cleave substantially faster, allowing for use of milder acids and lower temperatures. Effects upon an experimentally known lignin fragment model (containing the ubiquitous β-O-4 linkage) are next examined; this first required a mechanism refinement (3-step indirect cleavage, 1-step side reaction) and identification of the rate-limiting step under zero-force (thermal) conditions. Mechanochemical activation using very low stretching forces improves at first only yield, by fully shutting off the ring-closure side reaction. At only somewhat larger forces, in stark contrast, a switch in mechanism is found to occur, from 3-step indirect cleavage to the direct cleavage mechanism of simple ethers, finally strongly enhancing the cleavage rate of lignin. It is concluded that mechanochemical activation of the common β-O-4 link in lignin would improve the rate of its acidolysis via a mechanism switch past a low force threshold. Relevance to ball-milling experiments is discussed.     

1-(4-氯苯基)-2-环丙基酮肟醚的设计、 合成及杀虫活性

采用中间体衍生化方法, 以环唑醇中间体1-(4-氯苯基)-2-环丙基丙酮作为基本骨架, 引入肟醚活性片段, 合成了32个新的1-(4-氯苯基)-2-环丙基酮肟醚类化合物, 其化学结构经核磁共振波谱和质谱等确认. 单晶X衍射分析表明, 化合物2n属于单斜晶系, 空间群为P2₁/c. 生物活性筛选结果表明, 化合物1i在200 mg/L浓度下对蚜虫的致死率为78.57%; 化合物1g在200 mg/L浓度下对红蜘蛛的致死率为69.95%; 化合物1i在200和12.5 mg/L浓度下对黏虫的致死率分别为100%和85%.     

正相高效液相色谱法分析壬基环己醇聚氧乙烯醚中残留壬基环己醇

壬基环己醇聚氧乙烯醚(NCEO_n)是非环境友好型壬基酚聚氧乙烯醚(NPEO_n)潜在的升级换代产品。 本文采用正相高效液相色谱法(NP HPLC)测定产品中残存壬基环己醇(NC),用Weilbull法测定其中聚乙二醇(PEG)含量,用电喷雾电离质谱法评价聚氧乙烯(PEO)多分散指数(PDI),以此鉴定NCEO_n的品质。 为了建立快速分析NCEO_n产品中NC含量的方法,以满足跟踪检测的需求,本文筛选了反相HPLC和NP HPLC两类5种方法,并进行比较和初步条件优化,确定了用Inertsil NH₂色谱柱和示差折光检测器以及乙酸乙酯为洗脱液的NP HPLC法定量分析NC,方法的回收率为91.77%～107.6%,相对标准偏差为4.46%,最低检测限为9.8 μg/mL。 经测定,NCEO₇和NCEO₉产品中NC的残留量分别为0.158%和0.139%,PEG质量分数为7.1%和7.3%,PDI为85.0%和88.6%,证实NCEO_n产品具有NC残留量少、PEG含量低和产品PEO窄分布特征,具有在化妆品或个人洗护用品等民用产品中替代NPEO_n的潜能。     

一种表面共聚氢氧根选择性阴离子色谱固定相

报道了一种基于聚(苯乙烯-二乙烯基苯)微球(PS-DVB)的表面共聚氢氧根选择性阴离子固定相。它以烯丙基缩水甘油醚(AGE)为功能单体、通过自由基引发直接与PS-DVB微球表面残留的悬挂双键共聚,再通过醇胺开环得到。考察了两种醇胺试剂对分离的影响;扫描电镜、红外光谱、元素分析表征结果表明:表面共聚反应成功在微球表面引入季胺基团,且对微球理化性质无显著影响;所得固定相表现氢氧根淋洗液的高选择性,对常规无机阴离子表现出良好的分离性能(分离度>1.5)和运行稳定性(保留时间的相对标准偏差<1.13%),其实用性通过分析茶叶样品中无机阴离子进行了展示。     

黄体酮纳米胶束构建及体外释放行为

为了制备可缓释释放的黄体酮纳米胶束新剂型,构建了两嵌段聚合物载体聚乙二醇-聚丙烯基缩水甘油醚(PEG-PAGE),组装成胶束,对黄体酮担载,考察不同条件下的载药量和包封率,筛选出最佳比例,并进行体外释放研究。 结果表明,该胶束能够担载黄体酮,载药量为4.26%,包封率为21.30%,48 h内累计释放达61.31%,能够有效地延缓黄体酮的释放,为黄体酮纳米剂型的开发提供了实验和技术参考。     

蓖麻油聚氧乙烯醚水基润滑液摩擦学特性研究

本文以蓖麻油聚氧乙烯醚水基润滑液为研究对象,分别使用润滑膜厚度测量仪、微摩擦试验机和四球摩擦试验机对其成膜特性、摩擦磨损特性和抗磨极压特性进行了系统的研究,并用扫描电子显微镜和能量色散光谱仪对摩擦磨损机制进行了分析。结果表明：蓖麻油聚氧乙烯醚提高了纯水的成膜能力,能够在钢-铝摩擦副形成有效的润滑膜,起到良好的减摩抗磨效果。随着浓度的增大,对钢-铝摩擦副的减摩抗磨性能和四球摩擦试验的抗磨极压性能都得到了提高。     

Analysis of the pure-rotational spectrum in the ν28 = 1 excited torsional state and torsional couplings of trans-ethyl methyl ether

The trans-ethyl methyl ether molecule has three low-lying torsional modes, that is, two inequivalent methyl internal rotations and an asymmetric skeletal torsion. The internal rotations of the CCH₃ and OCH₃ methyl rotors and the skeletal torsion correspond to the vibrational modes, ν₂₈, ν₂₉ and ν₃₀ respectively. In this study, the microwave absorption spectrum in the ν₂₈ = 1 CCH₃ torsional state was analyzed for the first time. Nine hundred fifty seven lines up to J = 48 and K = 4 were assigned, and the rotational, centrifugal distortion and internal rotational tunneling parameters were determined with the use of a tunneling matrix formalism. By combining the present results on the ν₂₈ = 1 torsional state with those for the ν₃₀ = 1 skeletal torsional state and the ν₂₉ = 1 OCH₃ torsional state, torsional couplings are estimated in order to understand quantitatively the inverted A/E sequence patterns observed for those three excited torsional states.     

二乙二醇十八烷基醚单甲基丙烯酸酯及其聚合物的制备和表征简

以二乙二醇十八烷基醚和甲基丙烯酰氯为原料,采用醇钠-酰氯法合成了二乙二醇十八烷基醚单甲基丙烯酸酯(DEGOEMA),并利用自由基聚合得到聚(二乙二醇十八烷基醚单甲基丙烯酸酯)(PDEGOEMA). 采用凝胶渗透色谱(GPC)分析测试了PDEGOEMA的分子量和分子量分布. 通过傅里叶变换红外光谱(FTIR)、核磁共振氢谱(1H NMR)、差示扫描量热(DSC)、热重(TG)和X射线衍射(XRD)对DEGOEMA和PDEGOEMA的结构、相变行为、热稳定性和晶体结构进行了研究. 结果表明,这种新型单体及其聚合物是一种具有稳定的结构、良好的结晶性能、高相变焓及良好热稳定性的相变材料. PDEGOEMA的起始吸热温度为41 ℃,起始放热温度为36 ℃,热焓为73 J/g,在314 ℃以下热稳定性良好,可用于加工或使用温度较高的环境.     

含氟磺化双三蝶烯型聚芳醚砜质子交换膜的制备及性能

利用3,3,4,4-四氟二苯砜、十氟联苯、6F-双酚A及6,13-双三蝶烯二酚,通过亲核取代共聚及后磺化方法制备了2个系列不同磺化度的磺化双三蝶烯型聚芳醚砜,并通过氢核磁共振波谱(1H NMR)对其化学结构进行了表征.研究发现,所得磺化聚芳醚砜均表现出了优异的热稳定性.此类膜材料具有优良的机械性能、尺寸稳定性、氧化稳定性及高温低湿度条件下高的质子传导率.透射电子显微镜的结果表明,聚合物主链中大量氟原子的引入显著改善了聚合物的相分离结构,并且随着聚合物主链中氟含量的增加,亲水区域明显增大.这也是含氟磺化双三蝶烯型聚芳醚砜质子交换膜材料在高温低湿度条件下具有高质子传导率的主要原因.